Quantum mechanics makes some very significant observations about nature. Unfortunately, these observations remain a mystery because they do not fit into and/or cannot be explained through classical mechanics. However, we can still explore the philosophical and practical implications of these observations. This article aims to explain philosophical and practical implications of one of the most important observations of quantum mechanics – uncertainty or the arbitrariness in the behavior of particles.

Among all non conventional micro machining, electrochemical discharge machining ECDM is having high quality of material removal rate with zero residual stress. This machining has been accepted as a highly modern technology in micromachining. In this paper an effort has been done on micro drilling of glass using electrochemical discharge machining ECDM . A fixed tool and a step down transformer have been used to support the steady machining to increase the accuracy of work piece. The input parameters used in (...) this experiment are voltage, concentration of electrolyte, enter electrode gap and ratio of area of electrode. MRR has been investigated over the input parameters. Feed rate and electrolyte temperature has been made constant of 3µm sec and 30°c respectively. Taguchi method is used to optimize the effect of the process parameters on MRR. The signal to noise S N ratio and the ANOVA analysis are employed to find the contributions of input parameters. Vikrant Sharma | Sunil Kumar "Experimental research to Optimize Process Parameters in Machining of Non Conducting Material with hybrid non conconventional machining" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-1 | Issue-4 , June 2017. (shrink)

Electrochemical assisted abrasive flow finishing is a newly developed hybrid finishing process which is used to finish the internal parts of work piece having complicated geometry to large extent. In electrochemical assisted abrasive flow machining higher abrasion of the material was detected due to the combine effect of ECM and AFF processes. In Electrochemical aided abrasive flow machining a electrolyte is added to the prepared media .This media consist a kind of polymeric carrier and abrasive particles that are hydrocarbon gel, (...) Al2O3, Silicon based polymer, and NaI Sodium iodide as electrolytic salt. In this experimental research different process parameters such as voltage, abrasive concentration, Number of cycle, molal concentration and diameter of rod were considered at different levels for response characteristic of surface roughness Ra and material removal MR based on Taguchi method using standard L27 orthogonal array OA for the plan of experimentation. To determine the contribution of each parameter analysis of variance was used. Sandeep Singh | Sunil kumar "Experimental Research Work to Optimize Process Parameters into Electro Chemical Abrasive Flow Machining using Taguchi Methodology" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-1 | Issue-4 , June 2017 . (shrink)

The article deals with the relationship between faith and rational knowledge in modern Gaudiya Vaishnavism. It is shown that the position of modern Vaishnavas regarding revelation and critical knowledge is defined in the books of the reformer of Gaudiya Vaishnavism Bhaktivinoda Thakur. The positions of modern teachers of Gaudiya Vaishnavism – Bhaktivendanta Sadhu Swami and Dandi Maharaja are explained, the importance of their position for the development of interreligious dialogue in modern conditions is shown. The points of contact between (...) Gaudiya Vaishnavism and Christianity in matters of understanding time, eternity, revelation and rational cognition are shown. (shrink)

A collection of essays originally published in a special issue of Modern Asia Studies in March 2012, this volume comprises the interactions of various cultures including Singapore, Ladakh, Penang, and Istanbul. It also traces interactions over the sea and between various religious spaces. Businesses or inter-Asian joint-ventures are also included. Edited by professors of history, this book is a welcome addition to the scarce literature on transnational interactions within Asia.

Thakur Ramkrishna Paramhansadev was that divine soul whose magical lessons have exerted great influence upon the people not only in India but also in the whole world. The ‘Lokayata Siksha’ of Thakur Ramkrishnadev on religion like ‘Jata Mot Toto Poth’ (As different views, so different paths) reflects the divergent ways of worship to reach in the same destination. He proved that humanity is the best religion above all religions, castes and classes. The lesson taught by him proved that (...) one can achieve the eternal soul by different way of devotional practice and power of worship. Moreover, Ramkrishnadev also tried by himself in his lifetime to know the spiritual truth of life through different ways of practices guided by the people of different religions. He realized that the coordination of all religions under the single roof of society can make this world as a world of love to humanity. To serve the poor, ill and distressed people was the main mission of Thakur Ramakrishna, as is reflected in the workings of his great disciple Swami Vivekananda. Adopting a modern perspective, this paper attempts to highlight the importance of Sri Ramakrishna in religious integrity in India. (shrink)

Culturally the Indians were always “one”. The Titular Mughal Emperor was there to serve as a thread of unity among the Indians. The British showed disrespect to the Emperor which offended the Indians in General and the Muslims in special. India possesses its own economic system mainly based on agriculture and small industry. The foreign rulers were sending Indian raw-materials to Britain for feeding their new born industries and thus were exploiting Indian resources. The “Doctrine of Lapse” or “Escheat” policy (...) destroyed the Indian Industries. Indian Artisans, craftsman etc. became jobless and the burden of farmland increased. Poverty grabbed seriously the people. The Indian soldiers were paid low-salaries (starting from Rs. 7 to the end of Rs. 9). Indian soldiers were ill-treated in Army by the English causing rise of discrimination in their mind. The number of Indians in Army was far larger than the British sepoys (ratio 6:1). Most of the Indian soldiers were belong to Brahmin and Thakurs of East-India. A general discontent existed among all the Indian soldiers. Such dis-satisfaction were intensified by the Lord Canning introduction of “General Service Act” which required by the sepoys to march anywhere of British Empire. It is obvious that Indian sepoys had natural love and respect their motherland and faith of their own religion. The introduction of Enfield rifle with the cartridges greased with the fat of cow and pig, obnoxious to both the Hindus and Muslims set the spark that enkindled the embers of discontent of the Indian sepoy stored in them for a long time. (shrink)