The incorporation of thermal insulation materials into building walls is a novel strategy for reducing heating and cooling energy consumption. Nowadays, the issues of energy production, consumption, and energy storage have become global problems. Furthermore, the thermal insulation of buildings increases the thermal comfort of residential premises in order to save energy. The use of several kinds of thermal insulation materials is required in the construction sector. This paper compares the thermal and moisture performance of (...) two different types of walls. The buildings taken under consideration are located in two different Tirana neighborhoods, close to each other sharing similar climate parameters. Depending on the presence of thermal insulation, two types of walls were taken into consideration. A wall in which thermal insulation is not present and a wall with a ventilated façade system, are considered. Thermal insulation in the second case is made with rock mineral cotton. In order to obtain the most accurate results, pertinent temperature and humidity, measurements were made at several spots along the walls. The comparative analysis was performed using special measuring instruments. The temperature and moisture level in the internal walls and the temperatures of the external walls, at various spots on the walls, were taken into consideration, along with the layers of the relevant walls in both cases. The aim of this paper is to experimentally study the thermal performance of walls with various types of thermal insulation, including the ventilated façade system, as well as walls without thermal insulation. The purpose of the study is also to show how the technical and architectural methods utilized during construction affect the moisture and temperature fluctuations of the perimeter walls. (shrink)

This paper presents information about the moisture content and temperature level of brick walls in Tirana, Albania. The buildings whose walls have been studied were built in two different eras, throughout the twentieth century, and in more recent times. Given that during the second half of the twentieth century, Albania has been isolated from most of Europe and the West, and consequently the new architectural ideologies of the time, have not had the proper implementation there, the paper focuses on (...) the characteristic types of bricks used in Albania, the functions for which they are used, and their effectiveness in achieving comfort (thermal, moisture content control) during the two time periods mentioned above. Depending on the functions bricks perform in the walls studied in this paper, the walls are separated into two main groups: Walls in which bricks have structural role (red silicate brick walls, white silicate brick walls) and walls in which bricks do not have structural role (concrete block walls, holed brick walls). For all the types of bricks mentioned above, indoor moisture content and temperature measurements have been performed in all four cardinal directions. For the walls in which the bricks have a structural function, moisture measurements have been performed in all the facades of the buildings, because moisture in the bricks of these types of buildings, being a very important factor, directly affects the structural performance of the elements. The aim of the paper is to show the differences in moisture and temperature levels of the walls of these buildings, depending on the engineering and architectural techniques used during the building process, the use of insulation, and the masonry composition. (shrink)

Extruded polystyrene (XPS) otherwise known as a thermoplastic polymer has a closed cell structure and is often stronger, with a higher mechanical performance. XPS is a pressed material and is sold in different thicknesses ranging from 2 cm to 10 cm, thus having a weight that varies from 28 to 45 kg/m3 due to the force and pressure exerted on it. In general, XPS material has very low thermal conductivity and is resistant to bending. This material obtains typical values (...) of thermal conductivity between 0.025 and 0.040 W/m∙K., which means that it is ideal for surfaces that have to withstand weight, continuous traffic, etc. It is also resistant to moisture absorption and has a homogeneous density. Other characteristics of the material are good acoustic properties, easy assembly, and high durability over time. It should always be kept in mind that the surface where the thermal insulation will be applied must be leveled, cleaned, and dried. Primer is applied, before placing the thermal insulation on the surface. Then, XPS boards are placed on the surface, adhering to the corresponding mortar. This paper will deal with different cases of application of XPS tiles in the city of Tirana. A closer look at the resistance of this material from the day of application until today will be analyzed. The results during the observations showed high thermal stability of the material and no mold surface. EPS Expanded Polystyrene, otherwise known by the Dow Chemical trademark name STYROFOAM, is a lightweight product made from expanded plastic beads. It was first discovered by Eduard Simon in 1839 in Germany. EPS in its composition has 95% air and only about 5% plastic. This material is used because of its excellent properties, including good thermal insulation, good protective properties, and extremely lightweight. EPS is inert in nature and therefore does not result in any chemical reaction. EPS is durable, strong, and lightweight and can be used as an insulated panel system for facades, walls, roofs, and floors, as floating material in marine construction, and as a lightweight filler in road and railway construction. Different examples from the city of Tirana, of buildings where XPS and EPS materials are applied, are going to be analyzed, drawing conclusions. (shrink)

Albania is part of the emerging economies of the Western Balkan region. Polis University is one of the pioneering institutions in the field of architecture, built environment, and city sciences that represents innovative methodologies and concepts for educational and scientific purposes. Nowadays, many constructions in Albania involve a wide range of different materials. The building envelope is one of the main elements that provide protection from the outside environment but also the required thermal comfort for the inhabitants. The necessary (...) balance must be archived between energy efficiency and the durability of buildings. This paper will focus on the thermal performance and materials composition of two different types of masonry walls, a constituent part of Polis University's main building. The study will be based on an experiment using specific instruments to diagnose these typologies of wall composition. The results are further analyzed and compared. Specific instruments such as the thermal camera (Testo 882), U-value(Testo 435-2), and “Silverline Digital Moisture Meter” (from POLIS Energy lab) are engaged. The collected data are further interpreted through graphs, tables, and diagrams for both cases. It is observed that ventilated facades perform much better than standard facades, therefore their usage is strongly recommended. (shrink)

Purpose The purpose of this paper is to examine the feasibility and design of zero-energy buildings (ZEBs) in cold and semi-arid climates. In this study, to maximize the use of renewable energy, energy consumption is diminished using passive solar architecture systems and techniques. -/- Design/methodology/approach The case study is a residential building with a floor area of 100 m2 and four inhabitants in the cold and semi-arid climate, northeast of Iran. For thermal simulation, the climate data such as air (...) temperature, sunshine hours, wind, precipitation and hourly sunlight, are provided from the meteorological station and weather databases of the region. DesignBuilder software is applied for simulation and dynamic analysis of the building, as well as PVsyst software to design and evaluate renewable energy performance. -/- Findings The simulation results show a 30% decrease in annual energy consumption of the building by complying with the principles of passive design (optimal selection of direction, Trombe wall, shade, proper insulation selection) from 25,443 kWh to 17,767 kWh. Then, the solar energy photovoltaic (PV) system is designed using PVsyst software, taking into account the annual energy requirement and the system’s annual energy yield is estimated to be 26,291 kWh. -/- Originality/value The adaptive comparison of the values obtained from the energy analysis indicated that constructing a ZEB is feasible in cold and semi-arid conditions and is considered an effective step to achieve sustainable and environmentally friendly construction. (shrink)

Kruja is a middle-range city located in the center of Albania. The city of Kruja dates back to its existence from the V-VI century and extends to the city around the VI and IX centuries. It becomes the first capital of Albania in the XI-th century, specifically in 1190. This paper is going to deal with only two groups of buildings that are an integral part of the historical city of Kruja, the historical dwellings (XVIII century) and the socialist ones (...) (1960-1985). This paper aims to analyze through linear regressions the relation between two parameters: moisture content and temperature of the indoor walls and floors of the historic and socialist buildings in the city of Kruja. Three types of historic dwelling and three types of socialist apartments have been analyzed, relatively uniformly oriented. The measurements with specific instruments are done on the same day, for three hours. The degree of reactivity is different for both groups of buildings. The historical buildings are more sensitive to temperature rise. They respond invers to it (as the temperature rise, the level of the moisture content decreases), with a higher coefficient than socialist ones, and appear to be more efficient in reducing the level of the moisture, despite the average moisture content being higher. This paper takes into consideration also the analysis of the materials of the construction for both categories. If the level of moisture is reduced, the buildings will be improved and the quality of life indicators of the inhabitance will be improved too. (shrink)

Many countries in Eastern Europe, during the 1960–1970s, as well as Albania responded to the growing demand for new houses utilizing the emerging trends for industrialization of the construction process and mass construction of prefabricated residential buildings based on large-panel prefabricated RC elements. During the 1970s large-panel buildings spread throughout the country and became the main type of construction in the Albanian cities such as Shkodër, Tirana, Durrës, Elbasan, Berat, etc. Most of these buildings have five or six stories and (...) comprise different modules, the number of which depends on the urban and architectonic projects. The construction technology of these types of buildings included only the construction of prefabricated reinforced concrete material and did not take into account the energy performance of these structures. Since the moment of construction, only in the last year, several interventions have been made in different cities where a layer of polystyrene has been placed on the external walls of these buildings in order to enhance their thermal insulation. The aim of this paper is to improve the thermal performance of these buildings by introducing a comparison of their initial situation as they are today and how their performance would be if innovative technologies and materials were applied. The study is going to analyse the thermal performance of the existing buildings, by means of the thermal camera in the city of Kamez, located in Tirana, which has been chosen as a key study. Furthermore, the data obtained from the MEEC application are gathered, in order to compare the previous, the existing situation and the proposed intervention. The results may be used by municipalities of different cities, not only in the Albanian context, either where interventions have been made to improve their performance, or for municipalities where thermal regulation policies have not been yet implemented for these types of buildings. The existing situation of the buildings according to the calculations, showed a poor thermal performance, regardless of the fact that they are already equipped with thermal insulation building envelope. They have to be requalified in order to be categorized as a building with high thermal performance. (shrink)

This article presents information about facades, their thermal insulating role in buildings in Albania. The façade in construction is one of the necessary factors to ensure a longer life of the buildings and indoor thermal comfort. Façade systems are composed of different materials, which provide a protective effect during the life of the building. The article will focus on the characteristic materials used in Albania for the construction of facades and the main materials used from the year 2000 (...) up to today. The article will be informative, statistical, and comparative in order to draw conclusions. Nowadays building facades are again becoming one of the main subjects of discussion, undoubtedly due to the increasing importance of the building envelope in relation to energy consumption. In the 90s, minimal attention was paid to the efficiency and quality of facades; everything was done strictly in relation to residency requirements. But, during this last decade, Albania experienced a construction boom, with a series of good new buildings, which are accompanied by progress in the architectural style and in the techniques of building materials usage. However, the advantages of façade systems in construction are not only to make the building long-lasting. The function of facades always undergoes changes and advances over time, in terms of their impact on the temperature fluctuations inside the building or energy storage. (shrink)

The Plant Ontology (PO) is a community resource consisting of standardized terms, definitions, and logical relations describing plant structures and development stages, augmented by a large database of annotations from genomic and phenomic studies. This paper describes the structure of the ontology and the design principles we used in constructing PO terms for plant development stages. It also provides details of the methodology and rationale behind our revision and expansion of the PO to cover development stages for all plants, particularly (...) the land plants (bryophytes through angiosperms). As a case study to illustrate the general approach, we examine variation in gene expression across embryo development stages in Arabidopsis and maize, demonstrating how the PO can be used to compare patterns of expression across stages and in developmentally different species. Although many genes appear to be active throughout embryo development, we identified a small set of uniquely expressed genes for each stage of embryo development and also between the two species. Evaluating the different sets of genes expressed during embryo development in Arabidopsis or maize may inform future studies of the divergent developmental pathways observed in monocotyledonous versus dicotyledonous species. The PO and its annotation databasemake plant data for any species more discoverable and accessible through common formats, thus providing support for applications in plant pathology, image analysis, and comparative development and evolution. (shrink)

The study of biodiversity spans many disciplines and includes data pertaining to species distributions and abundances, genetic sequences, trait measurements, and ecological niches, complemented by information on collection and measurement protocols. A review of the current landscape of metadata standards and ontologies in biodiversity science suggests that existing standards such as the Darwin Core terminology are inadequate for describing biodiversity data in a semantically meaningful and computationally useful way. Existing ontologies, such as the Gene Ontology and others in the Open (...) Biological and Biomedical Ontologies (OBO) Foundry library, provide a semantic structure but lack many of the necessary terms to describe biodiversity data in all its dimensions. In this paper, we describe the motivation for and ongoing development of a new Biological Collections Ontology, the Environment Ontology, and the Population and Community Ontology. These ontologies share the aim of improving data aggregation and integration across the biodiversity domain and can be used to describe physical samples and sampling processes (for example, collection, extraction, and preservation techniques), as well as biodiversity observations that involve no physical sampling. Together they encompass studies of: 1) individual organisms, including voucher specimens from ecological studies and museum specimens, 2) bulk or environmental samples (e.g., gut contents, soil, water) that include DNA, other molecules, and potentially many organisms, especially microbes, and 3) survey-based ecological observations. We discuss how these ontologies can be applied to biodiversity use cases that span genetic, organismal, and ecosystem levels of organization. We argue that if adopted as a standard and rigorously applied and enriched by the biodiversity community, these ontologies would significantly reduce barriers to data discovery, integration, and exchange among biodiversity resources and researchers. (shrink)

This study assessed two motivational strategies and their respective ties to the service delivery in public universities in Cross River State. In achieving the central and specific targets of this research, four research questions and two null hypotheses were answered and tested in the study. The entire population of 440 security personnel in two public universities was studied, based on the census approach and following the ex-post facto research design. Three sets of expert-validated questionnaires, with Cronbach reliability estimates of 0.80, (...) 0.79 and 0.83 respectively, were used for data collection. Collected data were analysed using descriptive statistics and inferential statistics such as Pearson Product Moment Correlation and the One-way ANOVA. The level of incentives provision and security service delivery in universities was moderate. There were notable disparities between promotion, provision of incentives and security service delivery in universities. Security personnel discharged, on average, services beyond the extent of promotion and incentives provided to them. Provision of incentives did not relate significantly to security service delivery; however, staff promotion significantly influences security service delivery in universities. It was concluded that there are loopholes in the motivational practices of universities for security personnel. The service delivery of security personnel at universities in Cross River State is yet to be at an acceptable point that can promote institutional safety and goal attainment in the short- and long run. It was recommended, among other things, that security personnel who are due for promotion should not be denied such an opportunity, as it represents one of the strongest motivational factors in universities. (shrink)

The Plant Ontology (PO) (http://www.plantontology.org) (Jaiswal et al., 2005; Avraham et al., 2008) was designed to facilitate cross-database querying and to foster consistent use of plant-specific terminology in annotation. As new data are generated from the ever-expanding list of plant genome projects, the need for a consistent, cross-taxon vocabulary has grown. To meet this need, the PO is being expanded to represent all plants. This is the first ontology designed to encompass anatomical structures as well as growth and developmental stages (...) across such a broad taxonomic range. While other ontologies such as the Gene Ontology (GO) (The Gene Ontology Consortium, 2010) or Cell Type Ontology (CL) (Bard et al., 2005) cover all living organisms, they are confined to structures at the cellular level and below. The diversity of growth forms and life histories within plants presents a challenge, but also provides unique opportunities to study developmental and evolutionary homology across organisms. (shrink)

This paper determines the acoustic properties of external wall building materials composition. Noise pollution is one of the main pollutants nowadays but it is not considered of great importance in the construction field, despite some studies showing that greater acoustic pollution is produced by buildings under construction. The study consists of analysing two different types of buildings equipped with a different type of external masonry composition in terms of building materials. The buildings are located at “21 Dhjetori” street, Tirana, Albania. (...) Furthermore, the case study area is treated as an area that consistently harvests noise. The impact of noise pollution on the existing building materials is going to be analyzed. Those milestones will provide information regarding the noise levels, a comparison of the actual level of noise production (outdoor and indoor areas), sound transmission, and sound diminution, as well as the implementation of acoustic materials in order to improve the quality of life of the inhabitants. The selected area has the highest norms of acoustic pollution in the city according to the studies implemented by Determination of acoustic properties of building materials is an important task gaining higher importance due to the demand for suitable construction materials, located in places with high levels of noise and places with heavy traffic, such as in urban areas. The aim of this paper is to display a comparative study of the actual noise levels generated by this area. It indicates the acoustic properties of the current building materials followed by a more suitable soundproof insulation. (shrink)

The focus of the paper is the comparison between the two composite aluminum panels, respectively Alpolic and Durabond. The paper is going to explore their reaction when interacting with Tirana`s climatological factors and their tension strength through an experiment, in order to find out which panel displays the best performance. The construction urge is constantly evolving, especially in Tirana mostly because it is the main industrial and economical district of Albania. It is distinguished that innovative technology is being used in (...) facades of the new buildings. One of the features that finds massive use in façade coating in the city is the application of ventilated facades equipped with external aluminum composite panels. This paper is going to deal with two buildings with different typologies of external coating, including the different types of aluminum panels. The analysis will focus on identifying each panel property such as tension strength; their respond to various external factors; their thermal conductivity; and their manufacturing companies which have been selected and produced. Within this paper graphics displays of the records will be included, offering concentrated information and a high level of reliability for both aluminum composite panels. (shrink)

In this paper, we report on an experiment with The Walking Dead (TWD), which is a narrative-driven adventure game with morally charged decisions set in a post-apocalyptic world filled with zombies. This study aimed to identify physiological markers of moral decisions and non-moral decisions using infrared thermal imaging (ITI). ITI is a non-invasive tool used to capture thermal variations due to blood flow in specific body regions that might be caused by sympathetic activity. Results show that moral decisions (...) seem to elicit a significant decrease in temperature in the chin region 20 seconds after participants are presented with a moral decision. However, given the small sample involved, and the lack of significance in other regions, future studies might be needed to confirm the results obtained in this work. (shrink)

This paper is going to deal with water absorption in different types of wood such as: pine, oak, beech, and fir. The amount of water absorbed by these types of wood is known as water absorption and it is determined using the material's initial state and after their immersion in water. The major goal of this study is to explain the effects of water absorption in hardwood materials and to demonstrate the changes that will take place in them over the (...) course of 48 hours. Water can be absorbed by wood in a variety of ways, as a liquid, or as an atmospheric vapor. Despite the fact that wood can absorb other liquids and gases, water is the most important. Because of its hygroscopicity, wood, whether as part of a living tree or as a material, always contains moisture. The experiment will be focused on the selection of different types of wood (most popular in the Albanian context), analyzing their water absorption and moisture level. The wooden samples will be submerged in water for 24 and 48 hours in order to obtain the appropriate results. Their moisture level and water level due to capillarity will be analyzed too. The purpose of the study is to follow the behavior of wooden frames in different environments. (shrink)

Protein α-helices provide an ordered biological environment that is conducive to soliton-assisted energy transport. The nonlinear interaction between amide I excitons and phonon deformations induced in the hydrogen-bonded lattice of peptide groups leads to self-trapping of the amide I energy, thereby creating a localized quasiparticle (soliton) that persists at zero temperature. The presence of thermal noise, however, could destabilize the protein soliton and dissipate its energy within a finite lifetime. In this work, we have computationally solved the system (...) of stochastic differential equations that govern the quantum dynamics of protein solitons at physiological temperature, T=310 K, for either a single isolated α-helix spine of hydrogen bonded peptide groups or the full protein α-helix comprised of three parallel α-helix spines. The simulated stochastic dynamics revealed that although the thermal noise is detrimental for the single isolated α-helix spine, the cooperative action of three amide I exciton quanta in the full protein α-helix ensures soliton lifetime of over 30 ps, during which the amide I energy could be transported along the entire extent of an 18-nm-long α-helix. Thus, macromolecular protein complexes, which are built up of protein α-helices could harness soliton-assisted energy transport at physiological temperature. Because the hydrolysis of a single adenosine triphosphate molecule is able to initiate three amide I exciton quanta, it is feasible that multiquantal protein solitons subserve a variety of specialized physiological functions in living systems. (shrink)

Latent heat thermal energy storage technique has demonstrate to be a better engineering option mainly due to its benefit of supplying higher energy storage density in a smaller temperature difference between retrieval and storage. For this purpose, a micro electro-mechanical system, MEMS-based heat exchanger with microencapsulated PCM (MEPCM) slurry as cold fluid, has been simulated three dimensionally. This work investigates the influence of using MEPCM-slurry on the temperature of the cold and hot fluids. The MEPCM and water (...) properties have been considered temperature dependent. MEPCM-slurry is used with different volume fractions. The result shows that using MEPCM with 25% volume fraction leads to the improvement in fluids temperatures, that is, for hot fluid the rate of temperature reduction increases up to 23.5% and for cold fluid the rate of temperature rise decreases to 9%, compared to using only water in the MEMS. (shrink)

In this paper we identify and characterize an analysis of two problematic aspects affecting the representational level of cognitive architectures (CAs), namely: the limited size and the homogeneous typology of the encoded and processed knowledge. We argue that such aspects may constitute not only a technological problem that, in our opinion, should be addressed in order to build arti cial agents able to exhibit intelligent behaviours in general scenarios, but also an epistemological one, since they limit the plausibility of the (...) comparison of the CAs' knowledge representation and processing mechanisms with those executed by humans in their everyday activities. In the fi nal part of the paper further directions of research will be explored, trying to address current limitations and future challenges. (shrink)

Does the human mind resemble the machines that can behave like it? Biologically inspired machine-learning systems approach “human-level” accuracy in an astounding variety of domains, and even predict human brain activity—raising the exciting possibility that such systems represent the world like we do. However, even seemingly intelligent machines fail in strange and “unhumanlike” ways, threatening their status as models of our minds. How can we know when human–machine behavioral differences reflect deep disparities in their underlying capacities, vs. when such failures (...) are only superficial or peripheral? This article draws on a foundational insight from cognitive science—the distinction between performance and competence—to encourage “species-fair” comparisons between humans and machines. The performance/competence distinction urges us to consider whether the failure of a system to behave as ideally hypothesized, or the failure of one creature to behave like another, arises not because the system lacks the relevant knowledge or internal capacities (“competence”), but instead because of superficial constraints on demonstrating that knowledge (“performance”). I argue that this distinction has been neglected by research comparing human and machine behavior, and that it should be essential to any such comparison. Focusing on the domain of image classification, I identify three factors contributing to the species-fairness of human–machine comparisons, extracted from recent work that equates such constraints. Species-fair comparisons level the playing field between natural and artificial intelligence, so that we can separate more superficial differences from those that may be deep and enduring. (shrink)

In the future, when we compare the welfare of a being of one substrate (say, a human) with the welfare of another (say, an artificial intelligence system), we will be making an intersubstrate welfare comparison. In this paper, we argue that intersubstrate welfare comparisons are important, difficult, and potentially tractable. The world might soon contain a vast number of sentient or otherwise significant beings of different substrates, and moral agents will need to be able to compare their welfare levels. However, (...) this work will be difficult, because we lack the same kinds of commonalities across substrates that we have within them. Fortunately, we might be able to make at least some intersubstrate welfare comparisons responsibly in spite of these issues. We make the case for cautious optimism and call for more research. (shrink)

The concept of organizational stigma has received significant attention in recent years. The theoretical literature suggests that for a stigma to emerge over a category of organizations, a “critical mass” of actors sharing the same beliefs should be reached. Scholars have yet to empirically examine the techniques used to diffuse this negative judgment. This study is aimed at bridging this gap by investigating Goffman’s notion of “stigma-theory”: how do stigmatizing actors rationalize and emotionalize their beliefs to convince their audience? We (...) answer this question by studying the stigma over the finance industry since 2007. After the subprime crisis, a succession of events put the industry under greater scrutiny, and the behaviors and values observed within this field began to be publicly questioned. As an empirical strategy, we collected opinion articles and editorials that specifically targeted the finance industry. Building on rhetorical analysis and other mixed methods of media content analysis, we explain how the stigmatizing rhetoric targets the origins of deviant organizational behaviors in the finance industry, that is, the shareholder value maximization logic. We bridge the gap between rhetorical strategies applied to discredit organizations and ones used to delegitimize institutional logics by drawing a parallel between these two literatures. Taking an abductive approach, we argue that institutional contradiction between field and societal-level logics is sufficient, but not necessary to generate organizational stigma. (shrink)

It is often argued that the indispensability of continuum models comes from their empirical adequacy despite their decoupling from the microscopic details of the modelled physical system. There is thus a commonly held misconception that temperature varying across a region of space or time can always be accurately represented as a continuous function. We discuss three inter-related cases of temperature modelling — in phase transitions, thermal boundary resistance and slip flows — and show that the continuum view (...) is fallacious on the ground that the microscopic details of a physical system are not necessarily decoupled from continuum models. We show how temperature discontinuities are present in both data (experiments and simulations) and phenomena (theory and models) and how discontinuum models of temperature variation may have greater empirical adequacy and explanatory power. The conclusions of our paper are: a) continuum idealisations are not indispensable to modelling physical phenomena and both continuous and discontinuous representations of phenomena work depending on the context; b) temperature is not necessarily a continuously defined function in our best scientific representations of the world; and c) that its continuity, where applicable, is a contingent matter. We also raise a question as to whether discontinuous representations should be considered truly de-idealised descriptions of physical phenomena. (shrink)

I examine the once popular claim according to which interpersonal comparisons of welfare are necessary for social choice. I side with current social choice theorists in emphasizing that, on a narrow construal, this necessity claim is refuted beyond appeal. However, I depart from the opinion presently prevailing in social choice theory in highlighting that on a broader construal, this claim proves not only compatible with, but even comforted by, the current state of the field. I submit that all in all, (...) the most accurate philosophical assessment consists not in flatly rejecting this necessity claim, but in accepting it in a suitably revised form. (shrink)

Two major clarifications have greatly abetted the understanding and fruitful expansion of the theory of natural selection in recent years: the acknowledgment that interactors, not replicators, constitute the causal unit of selection; and the recognition that interactors are Darwinian individuals, and that such individuals exist with potency at several levels of organization (genes, organisms, demes, and species in particular), thus engendering a rich hierarchical theory of selection in contrast with Darwin’s own emphasis on the organismic level. But a piece of (...) the argument has been missing, and individuals at levels distinct from organisms have been denied potency (although granted existence within the undeniable logic of the theory), because they do not achieve individuality with the same devices used by organisms and therefore seem weak by comparison. We show here that different features define Darwinian individuality across scales of size and time. In particular, species-individuals may develop few emergent features as direct adaptations. The interactor approach works with emergent fitnesses, not with emergent features; and species, as a consequence of their different mechanism for achieving individuality (reproductive exclusivity among subparts, that is, among organisms), express many effects from other levels. Organisms, by contrast, suppress upwardly cascading effects, because the organismic style of individuality (by functional integration of subparts) does not permit much competition or differential reproduction of parts from within. Species do not suppress the operation of lower levels; such effects therefore become available as exaptations conferring emergent fitness—a primary source of the different strength that species achieve as effective Darwinian individuals in evolution. (shrink)

Climate change assessments rely upon scenarios of socioeconomic developments to conceptualize alternative outcomes for global greenhouse gas emissions. These are used in conjunction with climate models to make projections of future climate. Specifically, the estimations of greenhouse gas emissions based on socioeconomic scenarios constrain climate models in their outcomes of temperatures, precipitation, etc. Traditionally, the fundamental logic of the socioeconomic scenarios—that is, the logic that makes them plausible—is developed and prioritized using methods that are very subjective. This introduces a fundamental (...) challenge for climate change assessment: The veracity of projections of future climate currently rests on subjective ground. We elaborate on these subjective aspects of scenarios in climate change research. We then consider an alternative method for developing scenarios, a systems dynamics approach called ‘Cross-Impact Balance’ (CIB) analysis. We discuss notions of ‘objective’ and ‘objectivity’ as criteria for distinguishing appropriate scenario methods for climate change research. We distinguish seven distinct meanings of ‘objective,’ and demonstrate that CIB analysis is more objective than traditional subjective approaches. However, we also consider criticisms concerning which of the seven meanings of ‘objective’ are appropriate for scenario work. Finally, we arrive at conclusions regarding which meanings of ‘objective’ and ‘objectivity’ are relevant for climate change research. Because scientific assessments uncover knowledge relevant to the responses of a real, independently existing climate system, this requires scenario methodologies employed in such studies to also uphold the seven meanings of ‘objective’ and ‘objectivity.’. (shrink)

This article offers comprehensive criticism of the Turing test and develops quality criteria for new artificial general intelligence (AGI) assessment tests. It is shown that the prerequisites A. Turing drew upon when reducing personality and human consciousness to “suitable branches of thought” re-flected the engineering level of his time. In fact, the Turing “imitation game” employed only symbolic communication and ignored the physical world. This paper suggests that by restricting thinking ability to symbolic systems alone Turing unknowingly constructed “the wall” (...) that excludes any possi-bility of transition from a complex observable phenomenon to an abstract image or concept. It is, therefore, sensible to factor in new requirements for AI (artificial intelligence) maturity assessment when approaching the Tu-ring test. Such AI must support all forms of communication with a human being, and it should be able to comprehend abstract images and specify con-cepts as well as participate in social practices. (shrink)

In this article, we address an existing lacuna in the sociology of the senses, by employing sociological phenomenology to illuminate the under-researched sense of temperature, as lived by a social group for whom water temperature is particularly salient: competitive pool swimmers. The research contributes to a developing ‘sensory sociology’ that highlights the importance of the socio-cultural framing of the senses and ‘sensory work’, but where there remains a dearth of sociological exploration into senses extending beyond the ‘classic five’ (...) sensorium. Drawing on data from a three-year ethnographic study of competitive swimmers in the UK, our analysis explores the rich sensuousities of swimming, and highlights the role of temperature as fundamentally affecting the affordances offered by the aquatic environment. The article contributes original theoretical perspectives to the sociology of the senses and of sport in addressing the ways in which social actors in the aquatic environment interact, both intersubjectively and intercorporeally, as thermal beings. (shrink)

This article intends to analyze the performance and the efficiency of companies and to identify the key factors that may explain it. It was selected a sample with 15 enterprises: 7 Portuguese and 8 Ukrainian ones, belonging to several industries. Financial and non-financial data was collected for 6 years, during the period of 2009 to 2014. Research questions that guided this work were: Are the enterprises efficient/profitable? What factors influence enterprises’ efficiency/performance? Is there any difference between Ukrainian and Portuguese enterprises’ (...) efficiency/performance, which factors have more influence? Which industrial sector is represented by more efficient/profitable enterprises? The main results showed that in average enterprises were efficient with low level of profitability. According to gained results several indicators were highlighted so that companies would pay more attention to them. (shrink)

The article proposes to model the phenomenon of the cell phone as a wall-window. This model aims at explicating some of the perceptions and experiences associated with cellular technology. The wall-window model means that the cell phone simultaneously separates the user from the physical surroundings (the wall), and connects the user to a remote space (the window). The remote space may be where the interlocutor resides or where information is stored (e.g. the Internet). Most cell phone usage patterns are modeled (...) as a single dimension according to the level of distraction or attention of the user. In order to accommodate nuanced situations such as augmented reality, I suggest a two-dimensional layout: the wall-window. The wall represents the attention to the immediate physical environment, while the window represents the attention to a remote space. The wall-window model further evolves once a screen is woven into this layout. This addition is easily understood due to the screen’s etymology, which is associated with the concepts of shield or barrier. From a technical perspective, the screen has become an integral part of the cell phone. Furthermore, a screen itself is both a wall and a window. Lastly, once a cell phone is supplemented with a screen, it is easier to refer to it as media. And again, media fits into the wall-window model. (shrink)

In this essay, it is argued that naturalism of an even moderate sort speaks strongly against a certain widely held thesis about the human mental (and cognitive) architecture: that it is divided into two distinct levels, the personal and the subpersonal, about the former of which we gain knowledge in a manner that effectively insulates such knowledge from the results of scientific research. -/- An empirically motivated alternative is proposed, according to which the architecture is, so to speak, flattened from (...) above. On this flattened view, although the states and processes typically associated with the personal level likely appear in our best models of the production of human behavior, they appear alongside states and processes normally associated with the subpersonal level. Moreover, the success of such models depends nowise on a levels-based distinction between the various causal contributors. It is argued that the flattened view has methodological implications of significant import. (shrink)

To evaluate the overall good/welfare of any action, policy or institutional choice we need some way of comparing the benefits and losses to those affected: we need to make interpersonal comparisons of the good/welfare. Yet sceptics have worried either: that such comparisons are impossible as they involve an impossible introspection across individuals, getting ‘into their minds’; that they are indeterminate as individual-level information is compatible with a range of welfare numbers; or that they are metaphysically mysterious as they assume the (...) existence either of a social mind or of absolute levels of welfare when no such things exist. This article argues that such scepticism can potentially be addressed if we view the problem of interpersonal comparisons as fundamentally an epistemic problem – that is, as a problem of forming justified beliefs about the overall good based on evidence of the individual good. (shrink)

Talk of levels is everywhere in cognitive science. Whether it is in terms of adjudicating longstanding debates or motivating foundational concepts, one cannot go far without hearing about the need to talk at different ‘levels’. Yet in spite of its widespread application and use, the concept of levels has received little sustained attention within cognitive science. This paper provides an analysis of the various ways the notion of levels has been deployed within cognitive science. The paper begins by introducing and (...) motivating discussion via four representative accounts of levels. It then turns to outlining and relating the four accounts using two dimensions of comparison. The result is the creation of a conceptual framework that maps the logical space of levels talk, which offers an important step toward making sense of levels talk within cognitive science. (shrink)

It has been claimed that a key difference between ancient and contemporary skepticism is that, unlike the ancient skeptics, contemporary skeptics consider ordinary beliefs to be insulated from skeptical doubt. In the case of metaethics, this issue is related to the following question: what attitude towards ordinary moral thought and discourse should one adopt if one is a moral skeptic? Whereas moral abolitionists claim that one should do away with ordinary moral thought and discourse altogether, moral fictionalists maintain that, given (...) that morality produces practical benefits, one should continue to make moral utterances and have moral thoughts, while at the same time refraining from asserting such utterances and believing such thoughts. Focusing particularly on Mackie’s skeptical stance, the present essay considers whether the view that first-order moral beliefs are unaffected by moral skepticism is defensible, whether moral fictionalism is compatible with moral insulation, and whether contemporary moral skeptics are in general committed to there being insulation between first- and second-order levels. (shrink)

As known from the academic literature on Hinduism, the foreign, Persian word, “Hindu” (meaning “Indian”), was used by the British to name everything indigenously South Asian, which was not Islam, as a religion. If we adopt explication as our research methodology, which consists in the application of the criterion of logical validity to organize various propositions of perspectives we encounter in research in terms of a disagreement, we discover: (a) what the British identified as “Hinduism” was not characterizable by a (...) shared set of beliefs or shared outlook, but a disagreement or debate about basic topics of philosophy with a discourse on tenets of moral philosophy anchoring the debate; and (b), the Western tradition’s historical commitment to language as the vehicle of thought not only leads to the conflation of propositions with beliefs, but to interpreting (explaining by way of belief) on the basis of the Eurocentric tradition rooted exclusively in ancient Greek philosophy. Interpretation on the basis of the Western tradition leads to the Western tradition vindicating itself as the non-traditional, non-religious, rational platform—the secular—for explaining everything—the residua are what get called religions on a global scale. This serves the political function of insulating Western colonialism from indigenous moral and political criticism. Given that Western colonialism is the pivotal event, before which South Asians just had philosophy, and after which they had religion (the explanatory residua of Eurocentric interpretation), we can ask about Hindu religious belief. This only pertains to the period after colonialism, when Hindus adopted a Westcentric frame for understanding their tradition as religious because of colonization. Prior to this, the tradition the British identified as “Hindu” had a wide variety of philosophical approaches to justification, which often criticized propositional attitudes, like belief, as irrational. (shrink)

Both biosemiotics and evolutionary epistemology are concerned with how knowledge evolves. (Applied) Evolutionary Epistemology thereby focuses on identifying the units, levels, and mechanisms or processes that underlie the evolutionary development of knowing and knowledge, while biosemiotics places emphasis on the study of how signs underlie the development of meaning. We compare the two schools of thought and analyze how in delineating their research program, biosemiotics runs into several problems that are overcome by evolutionary epistemologists. For one, by emphasizing signs, biosemiotics (...) needs to delineate a semiotic threshold, which is a problem not encountered by evolutionary epistemologists. Instead, the latter recognizes that all organisms are knowers that evolve knowledge, which they recognize to extend toward phenomena produced by organisms such as behavior, cognition, language, culture, science, and technology. Secondly, biosemiotics attempts at continuing adaptationist notions on how organisms relate to their environment, while especially Applied Evolutionary Epistemology comes to redefine the nature of the organism–environment relationship in such a way that it recognizes the spatiotemporal boundedness of existence, which in turn makes adaptationist accounts obsolete. (shrink)

The aim of this paper is to analyse the people behaviour in different age buildings and different buildings typology. In the city of Kruja (Albania) exists mostly three types of buildings: the historical ones (medieval), the socialist ones (which belongs to the former communist regime) and the modern buildings. Each of them has different social and physics characteristics, different energy exchange and different building materials. The influence of all these characteristics in the exchange of energy and how they reflect in (...) changing the lifestyle of Kruja’s people is going to be analysed. A questionnaire will be undertaken to understand the way of life of Kruja’s people and to draw conclusions. A comparative analysis between all these typology of buildings will be undertaken in order to understand better the behaviour of Kruja’s people lifestyle living in these buildings. Although the conditions are not good, people tend to get a high level of place attachment and loyalty to the building they are living. The biggest energy consumers are the historical buildings and socialist ones; although the bills of the electricity are smaller than the third category they consume alternative energies and have major problems with thermal bridges. The most unfriendly categories are the socialist buildings. They prefer not to socialize much in comparison with the other two categories. (shrink)

there is a communication gap between hearing-impaired people and those with normal hearing, sign language is the main means of communication in the hearing-impaired population. Continuous sign language recognition, which can close the communication gap, is a difficult task since the ordered annotations are weakly supervised and there is no frame-level label. To solve this issue, we compare the accuracy of each model using two deep learning models, Inception and Xception . To that end, the purpose of this paper is (...) By attempting to translate sign language using deep learning models, we focused in this paper a comparing between Inception and Xception ¬¬¬¬¬ algorithm and compared it to previous papers in which we used VGG19[1], mobileNet [2], where we get in the Inception and Xception algorithm on the degree of Accuracy 99.32%, 99,43% respectively. number of images (29000 in the dataset in size 75*75 pixel ) and the data split training data into training dataset (70%) and validation dataset(15%) and testing dataset(15%) and 20 epoch. (shrink)

Premature birth or low birth weight (LBW) is predictor of infant morbidity and mortality. Generally, infant with premature birth will be treated on incubator device. Incubator must provide stable levels of temperature, relative humidity and oxygen concentration. Temperature on infant incubator must be maintaned around 36°C-38°C. In order to control that, adaptive Fuzzy- PI controller is proposed and implemented on infant incubator’s prototype. This research use DHT11 sensor as sensing element and the control method are actuated by lightbulbs. (...) The controller used Microcontroller Atmega16 as processor which output determines the amount of power supplied to the lightbulb by employing pulse width modulation and MOSFET triggered circuit. Tests were carried out on temperature references that correspond to the standard incubator temperature range of 36°C to 38°C. References changes (fluctuatif reference) test and disturbances test were also carried out to prove system performance. The tests result on fixed reference temperatures were able to reach a stable setpoint with time rise (tr) around the 200 second with the highest overshoot maximum steady state error below 5%. References change tests and disturbances test successfully proved the controller was able to follow changes in references and overcome the disturbances. (shrink)

Suspension system is used to fulfil the criteria of ride comfort and road handling. In this paper, a quarter car active & semi-active suspension systems are designed using Matlab/Script software. Comparison of active & semi-active suspension systems are done using robust control theory for the control targets suspension deflection, body acceleration and body travel. H infinity controller is selected to compare the two suspensions using time domain analysis. Finally the simulation result prove the effectiveness of the active suspension system by (...) decreasing the body acceleration & sustaining the suspension deflection and body travel outputs. (shrink)

Recently, active suspension system will become important to the vehicle industries because of its advantages in improving road managing and ride comfort. This paper offers the development of mathematical modelling and design of a neural network control approach. The paper will begin with a mathematical model designing primarily based at the parameters of the active suspension system. A nonlinear three by four-way valve-piston hydraulic actuator became advanced which will make the suspension system under the active condition. Then, the model can (...) be analyzed thru MATLAB/Simulink software program. Finally, the NARMA-L2, model reference and predictive controllers are designed for the active suspension system. The results are acquired after designing the simulation of the quarter-car nonlinear active suspension system. From the simulation end result using MATLAB/Simulink, the response of the system might be as compared between the nonlinear active suspension system with NARMA-L2, model reference and predictive controllers. Besides that, the evaluation has been made between the proposed controllers thru the characteristics of the manage objectives suspension deflection, body acceleration and body travel of the active suspension system. . As a conclusion, designing a nonlinear active suspension system with a nonlinear hydraulic actuator for quarter car model has improved the car performance by using a NARMA-L2 controller. The improvements in performance will improve road handling and ride comfort performance of the active suspension system. (shrink)

Abstract: In this research, an Artificial Neural Network (ANN) model was developed and tested to predict temperature in the surrounding environment. A number of factors were identified that may affect temperature or humidity. Factors such as the nature of the surrounding place, proximity or distance from water surfaces, the influence of vegetation, and the level of rise or fall below sea level, among others, as input variables for the ANN model. A model based on multi-layer concept topology was (...) developed and trained using data from several regions in the surrounding environment. The evaluation of testing the dataset shows that the ANN model is capable of correctly predicting the temperature with 100% accuracy. (shrink)

This study investigates the outlet temperature control for the design of steam condenser. The comparison has been made for a step drop in the steam condenser temperature set point using MATLAB/ Simulink environment for the steam condenser with NARMA-L2 using Levenberg-Marquardt algorithm and NARMA-L2 using resilient backpropagation algorithm controllers. The steam condenser with NARMA-L2 using Levenberg-Marquardt algorithm controller presented excellent and superior dynamic performance in response to the temperature drop in settling time. The overall simulation results demonstrated (...) that the steam condenser with NARMA-L2 using Levenberg-Marquardt Algorithm controller can be an efficient alternative to the steam condenser with NARMA-L2 using resilient backpropagation algorithm controller. (shrink)

Can the machines that play board games or recognize images only in the comfort of the virtual world be intelligent? To become reliable and convenient assistants to humans, machines need to learn how to act and communicate in the physical reality, just like people do. The authors propose two novel ways of designing and building Artificial General Intelligence (AGI). The first one seeks to unify all participants at any instance of the Turing test – the judge, the machine, the human (...) subject as well as the means of observation instead of building a separating wall. The second one aims to design AGI programs in such a way so that they can move in various environments. The authors of the article thoroughly discuss four areas of interaction for robots with AGI and introduce a new idea of techno-umwelt bridging artificial intelligence with biology in a new way. (shrink)

Can the machines that play board games or recognize images only in the comfort of the virtual world be intelligent? To become reliable and convenient assistants to humans, machines need to learn how to act and communicate in the physical reality, just like people do. The authors propose two novel ways of designing and building Artificial General Intelligence (AGI). The first one seeks to unify all participants at any instance of the Turing test – the judge, the machine, the human (...) subject as well as the means of observation instead of building a separating wall. The second one aims to design AGI programs in such a way so that they can move in various environments. The authors of the article thoroughly discuss four areas of interaction for robots with AGI and introduce a new idea of techno-umwelts bridging artificial intelligence with biology in a novel way. (shrink)

Are the most concerning consequences of light and noise pollution detrimental to human health? In my opinion, light and noise pollution may be causing a greater worry at the societal level by widening the gap between human generations living in cities and nature.

This Is A Review Of Multi-Disciplinary Research Articles On The Title Subject, Published In Various Peer Reviewed Journals, Professional Conferences, And Scientific Books, Including The Books Of Religions. (A) There Was A Time When Vedas Were Known All Over The World. You Can See The Influences Of Vedas In The Books Of All Modern Religions. For Example, Yoga And Yogic Powers Are Described In Bible And Also In The Books Of Judaism. There Are Many High Level Modern Yogis All Over (...) The World With Magical Powers. Saint Joseph Of Cupertino Has Demonstrated Levitation, Defying Gravity, And His Case Is Most Well Documented In The Western World. Yogic Powers Show Us That You Can Discover The Truth, Only By Observing The Nature, Just Like Galileo Did. (B) Unfortunately, Modern Science Has Abandoned The Approach Of Observing The Nature, And Has Gone On A Track Defined By Hypothesis, Assumptions, Experimentations Etc., To Discover The Truth. As A Result We Can Show That The Modern Science Lacks The Truth. We Do Not Know Even Gravity Correctly. We Do Not Know Why Placebo Medicine Works. (C) We See That Vedic Science Gives Us A Very Meaningful And Universal Definition Of Truth. Whereas The Modern Science Lacks Any Such Definition, Causing A Major Confusion In Research Activities. (D) The Vedic Science Also Has Another Very Crucial Difference – It Has Observed Two Types Of Causes: (I) Efficient Cause And (Ii) Material Cause, Behind Every Phenomenon. On The Other Hand Modern Science Considers Only The Material Cause. This Is Why Vedic Science Is Valid For The Entire Universe And For All Time, Past, Present, And Future. We Will Illustrate All Results Of Vedic Science With Observations In Nature. Such Examples Will Be Beyond Comprehension Of Modern Science. (E) This Research Will Show That There Is A Heaven And Hell Difference Between Modern Science And Modern Engineering. Modern Science Therefore Is Not And Cannot Be The Foundation Of Modern Engineering. (shrink)

This study aimed to compare the levels of self-esteem among Dire Dawa University Male Technology students for the program of computer science (CS), Information Technology (IT), Computer Engineering (CE). Subjects for this study were randomly selected. 90 students (30 in Computer Science, 30 in Information Technology, and a 30-in Computer Engineering) were selected as the subjects for this study. The self-esteem of the assessment, so that the student has been Prepared by Rekha Agnihotri self-confidence Inventory (ASCI). For the comparison between (...) groups at a value of 0.05, for a one-factor, an ANOVA test was performed. The results show that when a difference was found between the different disciplines of the male students had a higher level of self-esteem (p) Based on the results obtained, the conclusion was that the mean self-esteem scores of the students in Information Technology (27.57) are higher than that of the students in the Computer Science and Computer Engineering. (shrink)

In this paper, a Magnetic Levitation (MAGLEV) train is designed with a single degree of freedom electromagnet-based system that allows the train to levitate vertically up and down. Fuzzy logic, PID and Mras controllers are used to improve the Magnetic Levitation train passenger comfort and road handling. A matlab Simulink model is used to compare the performance of the three controllers using step input signals. The stability of the Magnetic Levitation train is analyzed using root locus technique. Controller output response (...) for different time period and change of air gap with different time period is analyzed for the three controllers. Finally the comparative simulation and experimental results demonstrate the effectiveness of the presented fuzzy logic controller. (shrink)

This paper presents the application of optimal control problem in modeling of stirred tank heater temperature control. The analysis of the open loop system shows that the system is not efficient without a controller. Linear Quadratic Gaussian (LQG) and Linear Quadratic Integral (LQI) controllers are used to increase the performance of the system. Comparison of the closed loop system with the proposed controllers have been done with Matlab/Simulink Toolbox and a promising results have been analyzed.